유튜브에서 난리난 정보 AIYIMA 튜브 T3 HiFi 프리 앰프 오디오 보드 진공관 6A2 포노 프리 앰프 축음기 프리 앰프 DIY 파워 사운드 앰프 기억하세요

-77%
$ 37,009
$ 48,077
4.7/5.0
무료 배송 

AIYIMA 튜브 T3 HiFi 프리 앰프 오디오 보드 진공관 6A2 포노 프리 앰프 축음기 프리 앰프 DIY 파워 사운드 앰프

상품 정보

여러분께 소개할 이 제품은 AIYIMA 튜브 T3 HiFi 프리 앰프 오디오 보드 진공관 6A2 포노 프리 앰프 축음기 프리 앰프 DIY 파워 사운드 앰프으로, 여러분의 생활을 더욱 편리하고 풍요롭게 만들어 줄 것입니다. 아래에서 제품의 특징, 사용 방법, 그리고 왜 이 제품이 여러분에게 이상적인지에 대한 상세한 정보를 제공하겠습니다. 정성껏 준비한 상품 설명을 통해, 여러분이 필요로 하는 최적의 선택을 할 수 있도록 도와드릴 것입니다.


Specifications:
 
Electrical level output:600mV @3mV 1KHz
SNR: ≥98dB
Working Voltage: DC12V
Product Dimension: L118.5*W98*H33MM
Frequency Response:Meet standard RIAA
Product Weight: 0.3kG
THD: 0.1%
Package Dimension: L235*W210*H65MM
 
 
Operation Steps:
 
1.The gear switch is in the OFF state.
2.Install the tube into the base of the tube according to the direction (the tube is not divided left or right, check whether the pin is deformed before installing the tube, and the deformation can be corrected by hand).
3.Connect the phono output cable to the audio MM input connector.
4.Connect the external equipment to the audio source output interface.
5.Connect the DC 12V power supply.
6.Rotate the switch to select the desired gear.
7.When the preamp input is input, the phono input will automatically switch to the preamp input.
 
 
Frequently Asked Questions:
 
Q:All the cables are connected, but no sound output?
A: 1. Check the POWER indicator is on, press the POWER button if the light is still off, At this point you can find a same output voltage power supply (must 12V) to check if the machine or power supply failure.If the POWER indicator light is on, check whether the corresponding input signal is selected correctly.
2.If the indicator light is on, check whether the VOL knob is in the minimum position. If so, turn clockwise to normal Volume
3.If both of the above are normal, check the input device if it is paused, mute, or the volume is minimized.
 
Q: Why does the sound is cracking?
A: This product is for the tube preamp, but also can be used as preamp, If post equipment is max volume & preamp too, it's easy to distortion, you just need to turn down the volume of the equipment, then ok.
 
Q: Why do loudspeakers make a lot of electric noise?
A: if you are not using the original factory standard power supply, please replace the power supply before testing.Many power supply in the market have large interference coefficient, which will cause a lot of current sound.
 
Q: Why the speaker has noise when I just plug in the input cable but don’t connect the sound sources ?
A:1.If you use unshielded signal lines, there will be interference signals entering the power amplifier. If you hate the sound, you are advised to use the shielded signal lines or unplug the signal lines.
2.Check if the grounding of the player is connected. If the ground wire is not connected, there will be a lot of noise.
 
Q: Why do I use MM to put input, it has no sound?
A: Check if the pre-stage input is still plugged in. If the pre-stage input is plugged in, then the input will not sound, and the pre-stage input line must be unplugged.
 
Q: Why the sound is very hard at the beginning, the 3 frequencies is not very clear, but normal after a day use?
A: The tube is a very sensitive device with good effect once the temperature should reach a degree commonly, normally about half an hour later the voice is very natural.
 
Q: Can I update the tube?
A: yes, we have tested and matched 6k4/6J1/6j4/GE5654/6ak5/66*1n,in our factory.It can be replaced directly.The sound will be different with different tube.
 
Q: Can I replace the tube without power off?
A: No, it is very easy to burn the tube,because the machine works under high voltage and the hot plug will damage the tube & machine,also will hurt the people.
 
 
Warning
 
1. Please do not open the shell without permission. Improper operation may cause the danger of electric shock.
2. Please use the power supply of the regular manufacturer, otherwise it will damage the machine.
3. Please do not use the machine in a high temperature and humidity environment.
4. When unplugging the input and output lines, please cut off the power supply first, otherwise the signal will damage the speaker.
 
 
 




Leave a Comment

WP Twitter Auto Publish Powered By : XYZScripts.com